01 Avoid oil only add not change
Oil in the use of diesel engine is essential, mainly plays the role of lubrication, cooling, cleaning and so on. Therefore, many drivers will pay attention to check the amount of oil in the lubricating oil and add it according to the standard, but they ignore the inspection of the quality of the lubricating oil and the replacement of the deteriorated oil, resulting in some engine moving parts always operating in a poor lubrication environment, thus accelerating the wear of the parts. Under normal circumstances, the loss of oil is not large, but it is easy to pollute, thus losing the role of protecting the diesel engine. During the operation of the diesel engine, a lot of dirt (carbon smoke, carbon and scale generated by incomplete combustion of the fuel) will enter the oil.
02 Avoid indiscriminate use of butter
(1) Butter the cylinder pad
Butter is a commonly used grease in engineering machinery repair, which can play the role of lubrication and sealing. Therefore, some repairmen will apply a layer of butter on the cylinder pad when installing the cylinder pad, believing that this can increase the tightness of the diesel engine. As everyone knows, this has affected the working performance of the diesel engine. The cylinder pad is the most important seal between the cylinder block and the cylinder head, which can not only seal the high temperature and high pressure gas produced in the cylinder, but also seal the cooling water and lubricating oil in the cylinder head and the cylinder block, so when disassembling the cylinder pad, special attention should be paid to its sealing quality.
(2) Butter the tire nuts
In order to easily tighten the nuts and prevent rust, many repairmen apply oil to the bolts and nuts of the tire. This is actually a mistake. Because after the tire nut is tightened, the threads have the characteristics of self-locking. This is because the helix Angle of the thread is less than the equivalent friction Angle between the threads. In a given bolt connection, the screw lift Angle is a certain value, and the equivalent friction Angle varies with the friction state between the threads. Obviously, the equivalent friction Angle between the threads decreases after oiling, and the self-locking performance of the bolted joint deteriorates. Therefore, do not grease or drop lubricating oil on the bolts and nuts of the tire. In doing so, it will loosen the nut and even cause an accident.

03 Do not install new cylinder liner and piston without selection
When replacing cylinder liner and piston, it is considered that the new cylinder liner and piston are standard parts, and they are interchangeable, and they can be used when installed. In fact, the size of the cylinder liner and piston have a certain tolerance range. If the largest size cylinder liner is matched with the smallest size piston, it will make the matching gap too large, resulting in weak compression and difficult to start. Therefore, when changing, it is necessary to check the size group code of the standard cylinder liner and piston, and the cylinder liner and piston must be installed so that the size group code of the standard piston and the size group code of the standard cylinder liner are the same, only in this way can we ensure that there is a standard fit gap between the two. In addition, each cylinder is installed with the same group code cylinder liner and piston at the same time, but also pay attention to the inspection of the cylinder plug gap before installation, in order to ensure the assembly standard, a test should be carried out before installation to prevent the installation of fake and shoddy defective products.
04 Do not check the plunger travel margin
In the test of the plunger fuel injection pump, many maintenance personnel do not pay attention to check the travel margin of the plunger. The so-called stroke margin of the plunger refers to the amount of movement that can continue to go up after the plunger is topped by the CAM on the camshaft. After adjusting the start time of the oil supply, the reason why the stroke margin is also checked is because the stroke margin of the plunger is related to the wear of the plunger and the sleeve. After the plunger and sleeve wear, the plunger needs to move up for a while before the oil can be supplied, thus delaying the start time of the oil supply. When the adjusting bolt is unscrewed or a thicker adjusting pad or gasket is used, the lowest position of the plunger is moved up, so that the travel margin of the plunger is reduced. Therefore, in the maintenance and commissioning of the injection pump, we should first check the travel margin to determine whether the injection pump is still allowed to adjust.
05 Do not measure the cylinder clearance when measuring the cylinder clearance, fail to measure the direction of the piston skirt perpendicular to the piston pin hole, and measure in other directions
The structure of the aluminum alloy piston is characterized by small upper and large lower, a cone, and the skirt section is elliptical, so the cylinder clearance along the circumference is not equal. When measuring, it is stipulated that the gap in the direction of the long axis of the ellipse shall prevail, that is, the gap in the direction of the piston skirt perpendicular to the piston pin hole shall be measured.Bulldozer








